Search Results

This standard covers general, dimensional, and performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, SAE 100R7, SAE 100R8, SAE 100R9, SAE 100R10, SAE 100R11, and SAE 100R12 hydraulic hoses set forth in the following sections.

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Hose (also includes hose assemblies) has a finite life and there are a number of factors which will reduce its life. This recommended practice is intended as a guide to assist system designers and/or users in the selection, installation, and maintenance of hose. The designers and users must make a systematic review of each application and then select, install, and maintain the hose to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list. WARNING: IMPROPER SELECTION, INSTALLATION, OR MAINTENANCE MAY RESULT IN PREMATURE FAILURES, BODILY INJURY, OR PROPERTY DAMAGE.

The procedures contained herein have been developed to establish a uniform method for comparative impulse testing of hydraulic hose assemblies with and without flexing in order to determine the effect of flexing on ultimate life of hose. The test method minimizes variables to give a comparison between flexing and non-flexing. Basic impulse test parameters are to be in accordance with SAE J343 except as modified to incorporate flexing. This test is not a requirement for SAE J517 hose.

This standard covers complete general and dimensional specifications for hose push-on fittings. These fittings are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figs. 1–3 and Table 2 are intended for use with low pressure hose and shall be retained by hose clamps as specified in SAE J536.

This standard covers general, dimensional, arid performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, SAE 100R7, SAE 100R8, SAE 100R9, SAE 100R10, and SAE 100R11 hydraulic hoses set forth in the following sections.

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of –40°F to +200°F (–40°C to + 93°C).

This standard is intended to document general and dimensional specifications for the various types and styles of hose fittings used in conjunction with hydraulic hoses specified in SAE J517, in hydraulic systems on construction and industrial equipment and commercial products. Also included are adapter unions. The basic design and dimensional features of the fittings shown are derived from existing industry practice and include the following types: Male Dryseal pipe thread type hose fittings shall be as shown in Figs. 1A-1C for the respective styles, and in Tables 1A-1F for the applicable hoses and sizes. Male straight thread O-ring boss type hose fittings shall be as shown in Figs. 2A and 2B for the respective styles, and in Tables 2A-2C for the applicable hoses and sizes. Male 37-deg flared type hose fittings shall be as shown in Figs. 3A-3C for the respective styles, and in Tables 3A-3F for the applicable hoses and sizes.

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

This standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. Flanged heads shall be as specified in Fig. 3 and Table 1. Split flange clamp halves shall be as specified in Fig. 4 and Table 1. Port dimensions and spacing shall be as specified in Fig. 5 and Table 2.

This specification covers seven types of air hose intended for use in automotive air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. Type G hose is to be used in frame and cab piping only, and only where air temperature is not in excess of 200 F. The types of hose are as follows: Type A–Hose shall be mandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.

This specification covers six types of air hose intended for use in automotive air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. The types of hose are as follows: Type A–Hose shall be mandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings. Type B–Hose shall be nonmandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.

This standard covers general, dimensional, and performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, and SAE 100R7 hydraulic hoses set forth in the following sections.

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

This specification covers five types of air hose intended for use in automotve air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. The types of hose are as follows:

This standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the “O” ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. Flanged heads shall be as specified in Fig. 3 and Table 1. Split flange clamp halves shall be as specified in Fig. 4 and Table 1. Port dimensions and spacing shall be as specified in Fig. 5 and Table 2.